Owon AG1022 Bedienungsanleitung

Dual-Channel Arbitrary Waveform Generator User Manual  AG1022  AG1012 WWW.OWON.COM.HK

4.Quick Start Front/Rear Panel and User Interface Front Panel ①②③④⑥⑰⑬⑮⑭⑯⑱⑩⑪⑦⑧⑨⑫⑤ Figure 4-1 Front panel overview ① LCD Display the user interface

4.Quick Start ⑪ Foot stool Make the instrument to be tilted for ease of operation ⑫ CH1 Output Control Turn on/off the output of CH1. The backlig

4.Quick Start ⑤ Fuse Use the specified fuse according to the voltage scale. ⑥ Power switch Switch between 110V and 220V. ⑦ USB Host port Connect as

4.Quick Start General Inspection After you get a new Waveform Generator, it is recommended that you should make a check on the instrument according to

4.Quick Start (1) Turn off the power button at the front panel and remove the power cord. (2) Check if the fuse installed before leaving factory (

5.Front Panel Operation 5. Front Panel Operation This chapter will deal with the following topics mainly:  How to Set Channels  How to Outp

5.Front Panel Operation To set channels  To Switch Channels for Display Press CH1/2 button to switch channel displayed on the screen between CH1 and

5.Front Panel Operation To set signals The following describes how to set and output Sine, Square, Ramp, Pulse, Noise, Arbitrary signals and DC. To

5.Front Panel Operation Figure 5-3: Set the frequency using number keys To Set the Amplitude Press F2 , confirm whether the "Ampl" me

5.Front Panel Operation The frequency range is 1μHz～5MHz; the period range is 200ns～1Ms. ChannelSetting menu of Square signalAmplitudeLoadOffsetCur

Mar.2014 edition V1.8 Copy Right in this Manual © Lilliput Company. All rights Reserved. The Lilliput's products are under th

5.Front Panel Operation Figure 5-5: Set the Duty cycle of Square signal To Output Ramp Signals Press button to call the user interface of Ramp

5.Front Panel Operation Term Explanation Symmetry: The percentage that the Rising Period takes up the whole Period. To Set the Symmetry (1) Pre

5.Front Panel Operation ChannelSetting menu of Pulse signalAmplitudeLoadOffsetCurrent signalFrequencyPulse widthParameter 2Parameter 3Parameter 1 Figu

5.Front Panel Operation Figure 5-9: Set the Pulse Width of Pulse signal To Output Noise Signals The noise signal which the generator output is whit

5.Front Panel Operation Offset/Low Level, Built-in Waveform, Editable Waveform. You can operate the menu by using the menu selection buttons on the r

5.Front Panel Operation (3) Turn the knob or press / direction key to choose the desired waveform. E.g. select ExpRise. Press F1 to output

5.Front Panel Operation storage path, choose Save, an input keyboard pops up, input the file name, and then choose DONE. How to Select a Stored Wave

5.Front Panel Operation Parameter 1DC Voltage Figure 5-12: The DC Setting Interface To recall wave file This function can read the waveform file with

5.Front Panel Operation Figure 5-13 Cut Wave Use waveform generators to recall wave: (1) Enter the operation menu: Press →Editable Wform →Sel

5.Front Panel Operation Figure 5-15 choose the .ota file (3) Choose Recall output. And the tip “Read file successfully” will show on the interface.

General Warranty Lilliput warrants that the product will be free from defects in materials and workmanship for a period of 3 years (1 year for acces

5.Front Panel Operation "FLASH". Otherwise, the storage menu will show "FLASH" only. (1) Install the U disk: insert a USB disk

5.Front Panel Operation To Set Display Parameter To Set the Bright (1) Press Utility and choose Disp Setup, press F1 to select Bright. (2

5.Front Panel Operation To Set Output Parameter To Set the Output Load For either of CH1 Output and CH2 Output on the Front panel, the Generator h

5.Front Panel Operation confirm. All the settings will be set to default. The default settings of the system are as follows: Output Default Function

5.Front Panel Operation To Set the Clock Source Provides a 20 MHz internal clock source and also accepts external clock source input from the [20MHz

6.Communication with PC 6. Communication with PC The Waveform Generators support communications with a PC through USB or COM port. You can use the ult

7.SCPI 7. SCPI The waveform generator supports SCPI, and the users can operate and control the device by USB and COM interface. For detailed informati

9.Technical Specifications 9. Technical Specifications All these specifications apply to the the waveform generator described in this document excep

9.Technical Specifications Waveform Characteristic Sine Flatness (when the Amplitude is 1.0 Vp-p (+4 dBm), relative to 1 kHz) AG1022 1 μHz to 10 MHz：

9.Technical Specifications Interfaces RS232, USB External Reference Clock Input Impedance 1 kΩ, AC coupled Requested Input voltage swing 100 mVp-p t

Table of Contents 1.General Safety Requirements ... 1 2.Safety Te

9.Technical Specifications Display Display Type 3.9 inch colored LCD (Liquid Crystal Display) Display Resolution 480 (Horizontal) × 320 (Vertical) Pix

10.Appendix 10. Appendix Appendix A: Enclosure Standard Accessories:  A power cord that fits the standard of the destination country  A USB

To Edit the File Name ... 2

1.General Safety Requirements 1. General Safety Requirements Before any operations, please read the following safety precautions to avoid any possib

2.Safety Terms and Symbols 2. Safety Terms and Symbols Safety Terms Terms in this Manual. The following terms may appear in this manual: Warning

3.General Characteristics 3. General Characteristics These products are dual-channel multi-function generator which combines Arbitrary Waveform

4.Quick Start 4. Quick Start This chapter will deal with the following topics mainly:  Front/Rear Panel Overview  User Interface Overview